View PC929PYJ000F_8052398.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pc929j00000f series 1. recognized by ul1577, file no. e64380 (as model no. pc929 ) 2. approved by vde, din en60747-5-2 ( ? ) (as an op- tion), file no. 94626 (as model no. pc929 ) 3. package resin : ul flammability grade (94v-0) ( ? ) din en60747-5-2 : successor standard of din vde0884 features agency approvals/compliance 1. inverter applications high speed, built-in short protection circuit, gate drive smd 14 pin ? opic photocoulper 1. 14 pin half pitch type (lead pitch : 1.27 mm) 2. double transfer mold package (ideal for flow soldering) 3. built-in igbt shortcircuit protector circuit 4. built-in direct drive circuit for igbt drive (peak output current : i o1p , i o2p : max. 0.4 a) 5. high speed responce (t plh , t phl : max. 0.5 s) 6. high isolation voltage (v iso(rms) : 4.0 kv) 7. lead-free and rohs directive compliant description pc929j00000f series contains an ired optically coupled to an opic chip. it is packaged in a mini-flat, half pitch type (14 pin). input-output isolation voltage(rms) is 4.0kv. high speed responce (t plh , t phl : max. 0.5 s). 1 sheet no.: d2-a06302en date jun. 30. 2005 ?sharp corporation notice the content of data sheet is subject to change without prior notice. in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. pc929j00000f series ? "opic"(optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and a signal-processi ng circuit integrated onto a single chip.
internal connection diagram truth table 2 sheet no.: d2-a06302en outline dimensions (unit : mm) pc929j00000f series input on off c input-output low level low level high level high level o 2 output high level low level low level low level fs output high level low level high level at operating protection function high level 1 2 3 4 5 6 7 cathode cathode anode nc ? nc ? nc ? nc ? 8 9 10 11 12 13 14 fs c gnd o 2 gnd ? no. to pin shall be shorted in the device. o 1 v cc amp. voltage regulator igbt protection circuit interface 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 7 1. smt gullwing lead-form [ex. pc929pj0000f ] 2. smt gullwing lead-form (vde option) [ex. PC929PYJ000F ] product mass : approx. 0.47g plating material : sncu (cu : typ. 2%) product mass : approx. 0.47g 1.27 0.25 pc929 6.5 0.5 date code 9.22 0.5 0.6 0.1 3.5 0.5 7.62 0.3 epoxy resin 0.35 0.25 0.26 0.1 8 7 1 14 primary side mark 1.0 + 0.4 ? 0 1.0 + 0.4 ? 0 10.0 + 0 ? 0.5 1.27 0.25 pc929 6.5 0.5 sharp mark "s" date code 9.22 0.5 0.6 0.1 3.5 0.5 7.62 0.3 epoxy resin 0.35 0.25 0.26 0.1 8 7 1 14 vde identification mark primary side mark 1.0 + 0.4 ? 0 1.0 + 0.4 ? 0 10.0 + 0 ? 0.5 4
date code (2 digit) a.d. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 mark a b c d e f h j k l m n mark p r s t u v w x a b c mark 1 2 3 4 5 6 7 8 9 o n d month january february march april may june july august september october november december a.d 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2nd digit month of production 1st digit year of production 3 repeats in a 20 year cycle sheet no.: d2-a06302en pc929j00000f series country of origin japan rank mark there is no rank mark indicator.
sheet no.: d2-a06302en electro-optical characteristics parameter symbol min. typ. max. unit input forward voltage t a = 25?c, i f = 0.2ma reverse current terminal capacitance t a = 25?c, v = 0, f = 1khz output supply voltage t a = ? 10 to + 60?c ? o 1 low level output voltage o 2 high level output voltage o 2 low level output voltage o 1 leak current high level supply current low level supply current t a = 25?c, v cc = v o1 = 24v, i f = 0 v cc = v o1 = 24v, i f = 0 v v a pf v v v v a ma ma ma ma t a = 25?c, i f = 10ma t a = 25?c, v r = 5v t a = 25?c, v cc = v o1 = 24v, i f = 5ma v cc = v o1 = 24v, i f = 5ma ? ? ? 15 15 ? 20 ? ? ? ? ? ? 1.2 ? 10 250 30 24 0.4 2.0 500 17 19 18 20 1.75 conditions v f1 v f2 i r c t v cc v o1l v o2h v o2l i o1l i cch i ccl v cc1 = 12v, v cc2 = ? 12v, i o1 = 0.1a, i f = 5ma v cc = v o1 = 24v, i o2 = ? 0.1a, i f = 5ma v cc = 24v, i o2 = 0.1a, i f = 0 t a = 25?c, v cc = v o1 = 35v, i f = 0 *8 *9 *9 *9 *9 *9 *9 *9 *9 ? 30 ? ? 22 v v ? 0.2 1.2 ? 10 ? 11 ? 1.6 1.5 (unless otherwise specified t a = t opr ) *8 it shall connect a by-pass capacitor of 0.01 f or more between v cc (pin 13 ) and gnd (pin, 10 , 14 ) near the device, when it measures the transfer characteristics and the output side characteristics. *9 fs=open, v c =0 absolute maximum ratings parameter symbol rating unit input forward current ma reverse voltage v output supply voltage v o 1 output current a a o 2 output current a a o 1 output voltage v power dissipation overcurrent detection voltage overcurrent detection current error signal output voltage error signal output current mw v ma v ma total power dissipation mw operating temperature ?c storage temperature ?c i f v r v cc i o1 i o1p i o2 i o2p v o1 p o v c i c v fs i fs p tot v iso (rms) t opr t stg t sol ?c *2 *1 o 1 peak output current *3 *3 *4 o 2 peak output current *5 *6 isolation voltage soldering temperature *1 the derating factors of a absolute maximum ratings due to ambient temperature are shown in fig.15 *2 t a =25?c *3 pulse width 0.1 5 s, duty ratio : 0.01 *4.5 the derating factors of a absolute maximum ratings due to ambient temperature are shown in fig.16 *6 ac for 1minute, 40 to 60 %rh, t a =25?c, f = 60hz *7 for 10s 20 6 35 0.1 0.4 0.1 0.4 35 500 v cc 30 v cc 20 550 4.0 ? 25 to + 80 ? 55 to + 125 260 kv *7 (unless otherwise specified t a = t opr ) 4 pc929j00000f series
sheet no.: d2-a06302en 5 pc929j00000f series parameter symbol min. typ. max. unit transfer characteristics protection output error signal output overcurrent detection t a = 25?c,v cc = v o1 = 24v, fs = open, v c = 0 v cc = v o1 = 24v, fs = open, v c = 0 isolation resistance rise time fall time overcurrent detection voltage overcurrent detection voltage hysteresis width o 2 "high low" propagation delay time at overcurrent protection o 2 "high low" output voltage at overcurrent protection error signal output pulse width o 2 fall time at o vercurrent protection low level error signal voltage high level error signal voltage instantaneous common mode rejection voltage (high level output) instantaneous common mode rejection voltage (low level output) ma ma ? s s s s kv/ s kv/ s v v s s v v a s s " low high " input threshold current t a = 25?c, v cc = v o1 = 24v, i f = 5ma, r g = 47 ? , c g = 3 000pf fs = open, v c = 0 t a = 25?c, v cm = 600v(p-p) i f = 5ma, v cc = v o1 = 24v, ? v o2h = 2.0v, fs = open, v c = 0 t a = 25?c, v cm = 600v(p-p) i f = 0, v cc = v o1 = 24v, ? v o2l = 2.0v, fs = open, v c = 0 t a = 25?c v cc = v o1 = 24v i f = 5ma, r g = 47 ? c g = 3 000pf, fs = open t a = 25?c, i f = 5ma v cc = v o1 = 24v i fs = 10ma, r g = 47 ? c g = 3 000pf, c = open t a = 25?c v cc = v o1 = 24v, i f = 5ma v fs = 24v, r g = 47 ? c g = 3 000pf, v c = 0 t a = 25?c, v cc = v o1 = 24v i f = 5ma, r fs = 1.8k ? r g = 47 ? , r c = 1k ? c g = 3 000pf, c p = 1 000pf t a = 25?c v cc = v o1 = 24v i f = 5ma, r g = 47 ? , c g = 3 000pf, r c = 1k ? , c p = 3 000pf fs = open 5 10 10 ? ? ? ? ? 1.5 1.5 v cc ? 6.5 1 2 ? ? ? ? 20 ? 0.3 0.2 ? 0.5 0.5 ? ? v cc ? 5.5 3 10 ? 2 0.4 100 5 ? 3.0 5.0 0.5 0.5 conditions "low high" propagation delay time "high low" propagation delay time response time i flh r iso t plh t phl t r t f cm l v cth v chis t pcohl t pcotf v oe v fsl i fsh t pcfhl ? t fs cm h t a = 25?c, dc = 500v, 40 to 60%rh ? 10 11 0.2 0.2 1.5 0.3 0.3 ? ? v cc ? 6 2 4 5 ? 0.2 ? 1 35 *11 *12 (unless otherwise specified t a = t opr ) *10 error signal "high low" propagation delay time *10 it shall connect a by-pass capacitor of 0.01 f or more between v cc (pin 13 ) and gnd (pin 10 , 14 ) near the device, when it measures the device, when it measures the overcurrent characteristics, protection output characteristics, and error signal output characteristics. *11 i flh represents forward current when output goes from "low" to "high" *12 v cth is the of c(pin 9 ) voltage when output becomes from "high" to "low"
sheet no.: d2-a06302en model line-up pc929j00000f pc929yj0000f ?????? approved lead form package model no. din en60747-5-2 pc929pj0000f PC929PYJ000F ?????? approved taping smt gullwing 1 000pcs/ reel sleeve 50pcs/ sleeve 6 please contact a local sharp sales representative to inquire about production status. pc929j00000f series
sheet no.: d2-a06302en fig.6 test circuit for high level / low level supply current fig.5 test circuit for "low high" input threshold current 7 pc929j00000f series fig.1 test circuit for o 1 low level output voltage fig.2 test circuit for o 2 high level output voltage fig.3 test circuit for o 2 low level output voltage fig.4 test circuit for o 1 leak current 3 2 1 13 12 11 10 9 8 14 v i f v o1l v cc1 v cc2 i o1 13 12 11 10 9 8 14 v i f v o2l v cc i o2 3 2 1 13 12 11 10 9 8 14 v i f variable v o2 v cc 3 2 1 13 12 11 10 9 8 14 v i f v 02h v cc i o2 3 2 1 13 12 11 10 9 8 14 i f v cc i o1l a 3 2 1 13 12 11 10 9 8 14 i f v cc i cc a 3 2 1
sheet no.: d2-a06302en 8 pc929j00000f series fig.7 test circuit for instantaneous common mode rejection voltage fig.8 test circuit for response time fig.9 test circuit for overcurrent detection voltage, overcurrent detection voltage hysteresis fig.10 test circuit for o 2 output voltage at overcurrent protection 13 12 11 10 9 8 14 v v o2 v cc sw b gnd gnd + ? ? v o2l v o2l ? v o2h v o2h a v cm v cm waveform v cm (peak) cm h , v o2 waveform sw at a, i f = 5ma cm l , v o2 waveform sw at b, i f = 0ma 3 2 1 13 12 11 10 9 8 14 r g c g v cc v in t r = t f = 0.01 s pulse width 5 s duty ratio 50% t plh t phl t f t r 10% 90% v out waveform 50% 50% v in waveform 3 2 1 v v out 1 2 3 13 12 11 10 9 8 14 r g c g v cc i f v v o2 v v cth 13 12 11 10 9 8 14 r g r c c g v cc i f v v o2 v c c p 1 2 3
sheet no.: d2-a06302en fig.12 test circuit for high level error signal current fig.11 test circuit for o 1 low level error signal voltage 9 pc929j00000f series fig.14 error signal "high low" propagation delay time, error signal output pulse width fig.13 test circuit for o 2 "high low" propagation delay time at overcurrent protection, o 2 fall time at overcurrent protection 13 12 11 10 9 8 14 r g c g v cc i f i fs v v fsl 3 2 1 13 12 11 10 9 8 14 r g c g v cc i f a v fs i fsh 3 2 1 v 13 12 11 10 9 8 14 v out r g r c c g c p v cc v in t r = t f = 0.01 s pulse width 25 s duty ratio 25% 3 2 1 v 13 12 11 10 9 8 14 r g r fs c g v cc v in t r = t f = 0.01 s pulse width 25 s duty ratio 25% r c 3 2 1 v out i f (input current) 90% 50% 10% t pcohl v oe t pcotf 90% error detection threshold voltage (v cth ) 10% ? t fs 50% 50% c (detecting terminal) fs (error signal output) t pcfhl v o2 (o 2 output voltage)
sheet no.: d2-a06302en 10 pc929j00000f series fig.15 forward current vs. ambient temperature fig.17 forward current vs. forward voltage fig.16 power dissipation vs. ambient temperature fig.19 "low high" relative input threshold current vs. ambient temperature ambient temperature t a (?c) power dissipation po, p tot (mw) ? 25 0 25 50 75 100 125 0 100 200 300 400 500 550 600 80 p tot p o 1.0 0.01 0.1 1 10 100 1.2 1.4 1.6 1.8 2.0 2.2 forward voltage v f (v) forward current i f (ma) 50?c 25?c 70?c t a = 0?c 0.4 0 0.2 0.6 0.8 1.6 1 1.2 1.4 ? 25 0 25 50 75 100 relative input threshold current i flh v cc = 24v ambient temperature t a ( c) i flh = 1 at t a = 25 c 60 50 40 30 20 10 0 02550758 0 100 125 ? 25 forward current i f (ma) ambient temperature t a ( c) fig.20 o 1 low level output voltage vs. o 1 output current 1 0.1 0.01 0.001 0.01 0.1 1 t a = 25 c v cc1 = 12v v cc2 = ? 12v i f = 5ma o 1 low level output voltage v o1l (v) o 1 output current i o1 (a) fig.18 "low high" relative input threshold current vs. supply voltage 1.6 1.4 1.2 1 0.6 15 18 21 24 27 30 0.8 t a = 25 c relative input threshold current i flh supply voltage v cc (v) value of v cc = 24v assumes 1.
sheet no.: d2-a06302en 11 pc929j00000f series fig.26 o 2 low level output voltage vs. ambient temperature fig.24 o 2 high level output voltage vs. ambient temperature fig.23 o 2 high level output voltage vs. supply voltage 24 23 22 21 20 19 ? 25 0 25 50 75 100 ambient temperature t a ( c) o 2 high level output voltage v o2h (v) i o2 = 0a v cc = 24v i f = 5ma i o2 = ? 0.1a 0.8 0.9 1 1.1 1.2 1.3 ? 25 0 25 50 75 100 ambient temperature t a ( c) o 2 low level output voltage v o2l (v) v cc = 24v i f = 5ma i o2 = ? 0.1a 35 30 25 20 15 10 5 15 18 21 24 27 30 o 2 high level output voltage v o2h (v) supply voltage v cc (v) t a = 25 c i f = 5ma i o2 = ? 0.1a fig.22 o 1 leak current vs. ambient temperature ? 25 10 ? 6 10 ? 7 10 ? 8 10 ? 9 10 ? 10 0255 075 100 ambient temperature t a ( c) o 1 leak current i o1l (a) v cc = v o1 = 35v i f = 0ma fig.21 o 1 low level output voltage vs. ambient temperature ? 25 0 25 50 75 100 0.2 0.15 0.1 0.05 0 ambient temperature t a ( c) o 1 low level output voltage v o1l (v) v cc1 = 12v v cc2 = ? 12v i f = 5ma i o1 = 0.1a fig.25 o 2 low level output voltage vs. o 2 output current 10 1 0.1 0.01 0.01 0.1 1 o 2 low level output voltage v o2l (v) o 2 output current i o2 (a) v cc = 24v t a = 25 c
sheet no.: d2-a06302en 12 pc929j00000f series fig.30 propagation delay time vs. ambient temperature fig.29 propagation delay time vs. forward current fig.31 overcurrent detecting voltage vs. ambient temperature 0.1 0.2 0.3 0.4 0.5 0 propagation delay time t phl , t plh ( s) t plh t phl v cc = 24v r g = 47 ? c g = 3 000pf i f = 5ma ? 25 0 25 50 75 100 ambient temperature t a ( c) 30 25 15 10 5 0 20 overcurrent detecting voltage v cth (v) v cc = 24v r g = 47 ? c g = 3 000pf i f = 5ma ? 25 0 25 50 75 100 ambient temperature t a ( c) 1 0.6 0.7 0.8 0.9 0.5 0.4 0.3 0.2 0.1 0 0510 15 20 25 forward current i f (ma) propagation delay time t phl , t plh ( s) t plh t phl t a = 25 c i f = 5ma r g = 47 ? c g = 3 000pf fig.27 high level supply current vs. supply voltage fig.28 low level supply current vs. supply voltage 18 16 14 12 10 8 6 low level supply current i ccl (ma) 15 18 21 24 27 30 supply voltage v cc (v) t a = 25?c t a = 80?c i f = 0ma t a = ? 25?c 16 14 12 10 8 6 4 t a = 25?c t a = 80?c high level supply current i cch (ma) 15 18 21 24 27 30 supply voltage v cc (v) i f = 5ma t a = ? 25?c 0 10 8 6 4 2 t pcohl t pcotf o 2 output fall time at protection from overcurrent t pcotf / o 2 "h-l" delay time at protection from overcurrent t pcohl ( s) v cc = 24v i f = 5ma r g = 47 ? c g = 3 000pf r c = 1k ? c p = 1 000pf ? 25 0 25 50 75 100 ambient temperature t a ( c) fig.32 o 2 output fall time at protection from overcurrent/o 2 "high-low" propagation delay time at protection from overcurrent vs. ambient temperature
sheet no.: d2-a06302en 13 pc929j00000f series v cc = 24v i f = 5ma r g = 47 ? c g = 3 000pf r c = 1k ? c p = 1 000pf 2 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 ? 25 0 25 50 75 100 ambient temperature t a ( c) o 2 output voltage at protection from overcurrent primary side mark v oe (v) 0 0.1 0.2 0.3 0.4 0.5 low level error signal voltage v fsl (v) v cc = 24v i f = 5ma i fs = 10ma r g = 47 ? c g = 3 000pf c = open ? 25 0 25 50 75 100 ambient temperature t a ( c) 10 ? 6 10 ? 7 10 ? 8 10 ? 9 high level error signal current i fsh (a) v cc = 24v i f = 5ma r g = 47 ? c g = 3 000pf v c = 0 ? 25 0 25 50 75 100 ambient temperature t a ( ? c) fig.34 o 2 output voltage at protection from overcurrent vs. ambient temperature fig.36 high level error signal current vs. ambient temperature fig.35 low level error signal voltage vs. ambient temperature 0 1.5 1.2 0.9 0.6 0.3 error signal "h-l" propagation delay time t pcfhl ( s) v cc = 24v i f = 5ma r fs = 1.8k ? r g = 47 ? c g = 3 000pf r c = 1k ? c p = 1 000pf ? 25 0 25 50 75 100 ambient temperature t a ( ? c) fig.33 error signal "high-low" propagation delay time vs. ambient temperature fig.37 error signal output pulse width vs. ambient temperature 0 50 40 30 20 10 error signal output pulse width ? t fs ( s) v cc = 24v i f = 5ma r fs = 1.8k ? r g = 47 ? c g = 3 000pf r c = 1k ? c p = 1 000pf ? 25 0 25 50 75 100 ambient temperature t a ( c) fig.38 overcurrent detecting voltage vs. supply voltage 0 5 10 15 20 25 added resistance = 0 ? 0.5k ? 1k ? 1.5k ? overcurrent detecting voltage v cth (v) 15 18 21 24 27 30 supply voltage v cc (v) t a = 25?c i f = 5ma v cc = 24v r g = 47 ? c g = 3 000pf r c = 1k ? fs = open c p = 1 000pf
sheet no.: d2-a06302en 14 pc929j00000f series fig.40 example of the application circuit (igbt drive for inverter) fig.39 overcurrent detecting voltage - supply voltage characteristics test circuit anode cathode pc929j00000f v cc o 1 o 2 c fs gnd r g r c v o2 c p c g v cc v c added resistance i f v v ?in order to stabilize the power supply line, we recommend to locate a bypass capacitor c b (0.01 f or more) between v cc and gnd near photocoupler. ?in order to stabilize the detecting voltage of pin-c, we recommend to locate a capacitor c p (approximately 1 000pf) between pin-c and gnd, and a resistor r c (approximately 1.0k ? ) between v cc and pin-c. however, the rise time of the detection voltage at pin-c varies along with the time constants of c p and r c . so, please make sure the device works properly in actual conditions. ?for the diode d, which is located between pin-c and collector of igbt, we recommend to use a diode that has the withstand voltage characteristic equivalent to igbt and also has little leak current. ?in order to prevent the failure mode or breakdown of pin-c from v ce variation of igbt, we recommend to locate a resistor r 2 (approximately 10k ? ) and a diode d1 at near pin-c, and a resistor r 3 (approximately 50k ? ) and a diode d 2 at between pin-c and gnd. this application circuit shows the general example of a circuit, and is not a design guarantee for right operation. pc929j00000f anode cathode ttl, micro computer, etc. v cc o 1 o 2 c c b c p f s gnd r g r c r 2 d 2 d 1 r 3 r 1 r fs pc817x etc. to micro computer + c fs ( + ) ( ? ) power supply cathode + v cc1 = 12v v cc2 = 12v
sheet no.: d2-a06302en 15 pc929j00000f series fig.41 operations of shortcircuit protector circuit remarks : please be aware that all data in the graph are just for reference and not for guarantee. 1. detection of increase in v ce(sat) of igbt due to overcurrent by means of c terminal (pin ) 2. reduction of the igbt gate voltage, and suppression of the collector current 3. simultaneous output of signals to indicate the shortcircuit condition (fs signal) from fs (pin ) terminal to the microcomputer 4. j udgement and processing by the microcomputer in the case of instantaneous shortcircuit, run continues. at fault, input to the photocoupler is cut off, and igbt is turned off. 9 8 anode ttl, micro computer, etc. amp. constant voltage circuit pc929j00000f igbt protector circuit v cc tr. 1 tr. 2 typ. 150k ? o 1 o 2 c v c fs gnd feedback to primary side cathode cathode v cc r g r c c p v ee igbt 3 2 8 9 10 14 11 12 13 1 interface
sheet no.: d2-a06302en 16 pc929j00000f series design considerations transistor of detector side in bipolar configuration may be damaged by static electricity due to its minute design. when handling these devices, general countermeasure against static electricity should be taken to avoid breakdown of devices or degradation of characteristics. notes about static electricity in order to stabilize power supply line, we should certainly recommend to connect a by-pass capacitor of 0.01 f or more between v cc and gnd near the device. we recommed to use approximately 1 000pf of capacitor between c-pin and gnd in order to prevent miss opration by noise. in the case that capacitor is used approximately 1k ? of resistance shall be recommended to use between v cc and c-pin however, the rise time of c-pin shall be changed by time constant of added cr, so that please use this device after confirmation. in case that some sudden big noise caused by voltage variation is provided between primary and secondary terminals of photocoupler some current caused by it is floating capacitance may be generated and result in false operation since current may go through led or current may change. if the photocoupler may be used under the circumstances where noise will be generated we recommend to use the bypass capacitors at the both ends of led. the detector which is used in this device, has parasitic diode between each pins and gnd. there are cases that miss operation or destruction possibly may be occurred if electric potential of any pin becomes below gnd level even for instant. therefore it shall be recommended to design the circuit that electric potential of any pin does not become below gnd level. this product is not designed against irradiation and incorporates non-coherent led. design guide
sheet no.: d2-a06302en ? for additional design assistance, please review our corresponding optoelectronic application notes. 17 pc929j00000f series degradation in general, the emission of the led used in photocouplers will degrade over time. in the case of long term operation, please take the general led degradation (50% degradation over 5 years) into the design consideration. please decide the input current which become 2 times of max. i flh . recommended foot print (reference) 1.8 1.27 1.27 1.27 1.27 1.27 1.27 0.8 9.0 (unit : mm)
sheet no.: d2-a06302en manufacturing guidelines reflow soldering: reflow soldering should follow the temperature profile shown below. soldering should not exceed the curve of temperature profile and time. please don't solder more than twice. soldering method flow soldering : due to sharp's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. flow soldering should be completed below 260?c and within 10s. preheating is within the bounds of 100 to 150?c and 30 to 80s. please don't solder more than twice. hand soldering hand soldering should be completed within 3s when the point of solder iron is below 400?c. please don't solder more than twice. other notices please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and pcb varies depending on the tooling and soldering conditions. 18 1234 300 200 100 0 0 (?c) terminal : 260?c peak ( package surface : 250?c peak) preheat 150 to 180?c, 120s or less reflow 220?c or more, 60s or less (min) pc929j00000f series
sheet no.: d2-a06302en solvent cleaning: solvent temperature should be 45?c or below immersion time should be 3 minutes or less ultrasonic cleaning: the impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of pcb and mounting method of the device. therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. recommended solvent materials: ethyl alcohol, methyl alcohol and isopropyl alcohol in case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. cleaning instructions this product shall not contain the following materials. and they are not used in the production process for this product. regulation substances : cfcs, halon, carbon tetrachloride, 1.1.1-trichloroethane (methylchloroform) specific brominated flame retardants such as the pbbos and pbbs are not used in this product at all. this product shall not contain the following materials banned in the rohs directive (2002/95/ec). ?ead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb), polybrominated diphenyl ethers (pbde). presence of odc 19 pc929j00000f series
sheet no.: d2-a06302en package specification 20 12.0 6.7 5.8 10.8 520 2 sleeve package package materials sleeve : hips (with anti-static material) stopper : styrene-elastomer package method max. 50 pcs. of products shall be packaged in a sleeve. both ends shall be closed by tabbed and tabless stoppers. the product shall be arranged in the sleeve with its primary side mark on the tabless stopper side. max. 20 sleeves in one case. sleeve outline dimensions (unit : mm) pc929j00000f series
sheet no.: d2-a06302en 21 tape and reel package package materials carrier tape : a-pet (with anti-static material) cover tape : pet (three layer system) reel : ps carrier tape structure and dimensions f k e i d j g b h h a c dimensions list (unit : mm) a 16.0 0.3 b 7.5 0.1 c 1.75 0.1 d 12.0 0.1 e 2.0 0.1 h 10.4 0.1 i 0.4 0.05 j 4.2 0.1 k 9.7 0.1 f 4.0 0.1 g 1.5 + 0.1 ? 0 5? m ax. a c e g f b d dimensions list (unit : mm) a 330 b 17.5 1.5 c 100 1.0 d 13 0.5 e 23 1.0 f 2.0 0.5 g 2.0 0.5 pull-out direction [packing : 1 000pcs/reel] reel structure and dimensions direction of product insertion pc929j00000f series
?the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. ?contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. ?observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- office automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - -- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traffic signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii) sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment - -- medical and other life support equipment (e.g., scuba). ?if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. ?this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. ?contact and consult with a sharp representative if there are any questions about the contents of this publication. 22 sheet no.: d2-a06302en important notices pc929j00000f series [e228]

▲Up To Search▲

Price & Availability of PC929PYJ000F

	To Download PC929PYJ000F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .